Concrete cutting in Kingman AZ - a clean cut, planned before the saw starts
Need a slab opened for a pipe, a doorway or new concrete? We plan the cut, the water and any buried lines first.
- Licensed and fully insured.
- Free on-site estimates.
- We respond within 1 business day.
What does concrete cutting involve, and who should do it in Kingman?
The short answer: Concrete cutting means sawing or core drilling through a slab so you can take out a broken section, run a pipe or wire underneath, or tie new concrete into old. At Kingman Concrete Company we do this work for homes and small businesses in Kingman, AZ.
Thank you for looking into this before anyone starts a saw. Usually a cut is part of something bigger. A plumber needs to reach a line, one square of the driveway has dropped, or you want a patio to meet the house. The price mostly depends on how long and deep the cut runs, how much steel is inside the slab, whether the work is indoors, and whether the broken concrete gets hauled away or patched afterward. The schedule depends less on the saw than on getting buried lines marked and, when the job needs one, a permit. I'll go over both when I come out, and the estimate gives you the figure for your own job.
How do you know your slab needs to be cut?
One section cracked and sunk
When one square of your driveway or patio has cracked and dropped while the rest sits flat, the dirt under that piece has usually settled or washed out. Cutting out that section and replacing it is often less work than a whole new slab, but the broken edges keep chipping and letting water under the sections next to it the longer it sits.
A leak or line underneath
Wet spots, a drain that keeps backing up or a plumber's diagnosis can mean the problem is under the concrete, so the slab has to be opened before the line can be fixed. A leak left running keeps softening the ground the slab sits on, which makes the repair bigger.
New work meeting old concrete
If you want to widen a drive, extend a patio or add a drain, the old slab usually needs a straight cut where the new work joins it. New concrete poured against a ragged broken edge tends to leave a weak seam, and that seam is usually where cracking and lifting start.
What our concrete cutting work includes
Before the saw starts, I ask where the cut goes, whether it's indoors and what might be buried nearby, because those answers decide how we handle the water, the dust and getting lines marked. Then we mark the cut line with you so it lands where you want it, protect the area around it, make the cut, break out and haul away the concrete, and clean up. If new concrete is going in, we leave a straight edge for it to tie into so the old and new sections meet cleanly.
Most cuts lead to more concrete. If you're widening a drive or replacing a cracked section, the cut sets up the new pour for our concrete driveway building work. A back patio extension usually starts the same way, with a clean cut on the old slab before concrete patio construction ties the new section in.
Removing a damaged section
This suits you if most of the slab is flat and sound and only one piece has failed. You replace the bad section and keep the rest, which usually costs less than tearing everything out.
Openings for pipes and drains
This suits you when a plumber or electrician needs to get under or through the slab. We cut only what the job needs, and a single pipe can often go through a small round core hole instead of a long trench.
Cuts inside the house or garage
This suits you if you're adding a floor drain, moving plumbing or opening a garage slab. Indoor work takes more planning, because the water and dust have to be handled inside a room instead of running off into the yard.
What happens after you call us about concrete cutting in Kingman?
Here's how a cutting job runs with us, from your first call to the walk-through at the end, and who you'll be dealing with at each step.
- Step 01
Call and set a visit
When you call, we set a time for me to come out, look at the slab and hear what you need cut. I'll also ask about anything you know is buried nearby, like a sprinkler or pool line.
- Step 02
Get your estimate and permit check
After the visit you get an estimate, so you know the price before any date is set. Before we schedule the work, we look up which office covers your address.
- Step 03
Lines marked, then the cut
If the job includes digging, nothing starts until the buried lines are marked. Our own crew then sets up, cuts, breaks out the concrete and cleans up, and I run the work on site.
- Step 04
Walk the finished job together
When the cut and cleanup are done, we walk the job with you. If a new pour follows, we go over what comes next before we leave.
Concrete cutting in Kingman, and who handles the permit
Whether your cut needs a building permit depends on the job, and the office that covers your address makes that call. That may be the city or the county. Before we set a date, we look up which one it is and take care of the permit application when the job needs one. For addresses inside the city, applications go through the City of Kingman's public portal, where you can also see inspection results. The city lists 928-753-8130 and buildingadmin@cityofkingman.gov for questions about applications and inspections.
Around Kingman, much of our cutting is on driveways and patios where one piece has failed or a new section needs to tie in, plus garage slabs that need opening for a drain or line. We do the same work in the cities around it, including New Kingman-Butler and Golden Valley, and if your address isn't on our list, please ask us anyway.
Get a free estimate for your concrete cut
Send the form and we'll reply within one business day to set a time for me to come out and look at the slab. The estimate is free and done on site, and you're under no obligation to book the work.
Why Kingman homeowners call Kingman Concrete Company
I see your cut myself
I come out to look at the job and give the estimate myself, and I run the work on site with our own crew. The person who planned the cut is there when the saw starts.
Planning habits from city work
I learned concrete on a municipal crew pouring curbs, walks and slabs, where every pour was planned carefully and checked the same way. We've been in business since 2020, and we still work that way.
Licensed and fully insured
We're licensed and fully insured. That matters on a bigger cut or one that needs a permit, because Arizona leaves that work to licensed contractors.
The job explained before booking
Before anything is scheduled, I go over where the cut goes, what might be under it and what happens to the opening afterward. You know what we're doing and why before the crew shows up.
On a cutting job, most of the work that counts happens before the saw starts. Tell us about your cut and I'll come out to look at it.
Concrete cutting questions from Kingman homeowners
How much does concrete cutting cost in Kingman, AZ?
There isn't a set price we can quote online, because two cuts of the same length can be very different jobs. I price the work after seeing the slab, how easy it is to reach and what happens to the opening afterward, and you'll have that price before any date is set.
Can someone without a contractor license cut concrete in Arizona?
Only for small jobs. Arizona lets an unlicensed person take casual or minor work under $1,000 in total, counting labor and materials, but that exemption ends once the work needs a local building permit, so a bigger or permitted cut calls for a licensed contractor. If you do the work on your own home yourself, and it isn't for sale or rent, contractor licensing doesn't apply to you.
Do utility lines need to be marked before concrete cutting in Kingman?
Yes, when the job includes digging. Nobody can start excavating until all utilities are marked, and a violation can bring a fine of up to $5,000 each time. Utility owners have 48 hours to mark their lines, so we plan for that wait. They mark only what they own, usually up to the meter, so for private lines like a water line to a pool, Arizona 811 suggests hiring a private locating company.
Will concrete cutting make a mess of dust and water?
There will be water, and it's there to control the dust. Under a federal safety rule for employers, a hired crew cutting with a handheld saw uses a built-in system that keeps water running to the blade, and core drills feed water to the hole the same way. Plan for wet ground around the work area while we cut.
How do I get ready for concrete cutting inside my house?
Clear the room, and ask the crew how they'll get the dust out. For indoor work, employers have to provide a way to exhaust the air as needed so visible dust doesn't build up in the room. We'll go over where the water goes and how the room is protected when I come out.
What is the best way to fix one cracked section of a concrete slab?
If the rest of the slab is flat and sound, cutting out the bad section and pouring a new one is usually better than tearing everything out. A section usually breaks because the dirt under it settled or washed out, so the ground underneath is the part to get right. I'd rather put the budget into packing that ground properly than into a fancy finish, because a new piece poured over the same soft spot tends to sink again.
Concrete work that often follows a cut
Concrete driveway building
When the cut is the start of a wider drive or a replaced panel, a new driveway pour needs a packed base and a clean edge to meet.
Concrete patio construction
If you're adding on to a back patio or replacing a sunken section, a new pour ties into the old slab and needs its own solid ground.
Call us about your concrete cut
Call (928) 391-0060 or use the form. If you can tell us where the cut goes, whether it's indoors and any private buried lines you know of, I can plan the visit before I come out.